suspension-banner

SOFTAIL AIR SUSPENSION (SAS)

sas_web-banner
You can raise and lower the bike at the touch of a button.

Add extra air to compensate for you passenger, then release some for solo riding. You can also release all the air and park your bike down on the ground. Adjustable air pressure make for smooth comfortable ride under any condition. No more bottoming out.

SAS-00

Fits Softail models 2000 to 2017  and FXSB Breakout® 2013-2017

SAS-99

Fits 1999 & earlier Softail frames

SAS-XL

Fits 1999 & earlier Softail frames

SAS XL versions have an added 5/8″ length to the cylinder housing – giving you about 2″ more travel at the swing arm for a total of approx 6″. Ideal for custom bikes that are extra low and need the extra lift to raise the bike to a rideable height.

MUELLER LOWERING KITS

PW-448-200

Suits 18-19 18-19 M8 FXBR, FXFB, FXFBS, FLDE, FLFB, FLHC, FXBRS, FLSB

Lowers by up to 35 mm (1.3″) on FXBR models (40 mm (1.5″) for show purposes)
•Stepless lowering by up to 35 mm (1.3″) on FXBB models
•No re-pressing of the original needle bearing necessary as they are already delivered with bearings
•Installation without shortening the threaded rod

PW-448-201

Suits 18-19 18-19 M8 FXBB, FXLR, FLSL

Lowers by up to 35 mm (1.3″) on FXBR models (40 mm (1.5″) for show purposes)
•Stepless lowering by up to 35 mm (1.3″) on FXBB models
•No re-pressing of the original needle bearing necessary as they are already delivered with bearings
•Installation without shortening the threaded rod

PW-130-10

For FXST / FLST models 89-99

Individually adjustable from 0 – 40mm (0″ – 1.5″)
For show purposes a lowering up to 80mm (3″) is possible
No re-pressing of the original bearings on EVO models
Height adjustment even when installed on Twin-Cam models
Suspension can also be up to 30mm (1″) higher on Twin-Cam models

PW-130-20

For FXST / FLST models 00-17

Individually adjustable from 0 – 40mm (0″ – 1.5″)
For show purposes a lowering up to 80mm (3″) is possible
No re-pressing of the original bearings on EVO models
Height adjustment even when installed on Twin-Cam models
Suspension can also be up to 30mm (1″) higher on Twin-Cam models

IOMP SWINGARM PIVOT BLOT COVERS

SWINGARM PIVOT BOLT COVERS

Suits 08-17 FXST Models
Gloss black swingarm pivot axle covers made of CNC machined high-strength aluminum
• Both covers are clamped with a VA grub screw for a nice clean look
• Sold in Pairs

SWINGARM PIVOT BOLT COVERS

Suits 18-UP FXST Models
• Gloss black swingarm pivot axle covers made of CNC machined high-strength aluminum
• The cover is clamped with a VA grub screw for a nice clean look
• Sold Each

SWINGARM PIVOT BOLT COVERS

Suits 19-UP FXDR Models
Gloss black swingarm pivot axle covers made of CNC machined high-strength aluminum
• The cover is clamped with a VA grub screw for a nice clean look
•  Sold Each

THUNDERBIKE SWINGARM PIVOT BLOT COVERS

LEFT SWINGARM PIVOT BOLT COVER BLACK

Suits 18-UP FXST Models
Gloss black swingarm pivot axle covers made of CNC machined high-strength aluminum
• Sold Each

RIGHT SWINGARM PIVOT BOLT COVER BLACK

Suits 18-UP FXST Models
Gloss black swingarm pivot axle covers made of CNC machined high-strength aluminum
• The left axle cover #TB-22-74-130 is required for mounting the right cover.
• Sold Each

LEFT SWINGARM PIVOT BOLT COVER POLISHED

Suits 18-UP FXST Models
Polished swingarm pivot axle covers made of CNC machined high-strength aluminum
• Sold Each

RIGHT SWINGARM PIVOT BOLT COVER POLISHED

Suits 18-UP FXST Models
Polished swingarm pivot axle covers made of CNC machined high-strength aluminum
• The left axle cover #TB-22-74-140 is required for mounting the right cover.
• Sold Each

IOMP SHOCK BOLT COVERS

SHOCK BOLT COVERS

Suits 18-UP M8 Models
Gloss black shock bolt covers made of CNC machined high-strength aluminum
• Both covers are clamped with a VA grub screw for a nice clean look
• Sold Each

IOMP TOP FORK BOLT COVERS

TOP FORK BOLT COVERS

Suits 13-17 FXSB Models (Will not fit CVO models)
• Black powder coated top fork caps
• Covers are clamped by a grub screw
• Sold in Pairs

TOP FORK BOLT COVERS

Suits 18-UP FXST Models
• Black powder coated top fork caps
• Covers are clamped by a grub screw
• Sold in Pairs

THUNDERBIKE TOP FORK BOLT COVERS

TOP FORK BOLT COVERS

Suits 18-Up FXBR Models
• Black powder coated top fork caps
• Covers are clamped by a grub screw
• Sold in Pairs

IOMP UPPER FORK COVERS

UPPER FORK COVERS

Suits 13-17 FXSB Models
• Black high-strength aluminum upper fork tube covers to suit 13-17 Breakout models with 49mm fork tubes
• Made to fit exactly between the top & bottom of the triple trees with no gap & no rattle
• Sold in Pairs

UPPER FORK COVERS

Suits 18-UP FXBR Models
• Black high-strength aluminum upper fork tube covers to suit 18-UP Breakout models with 49mm fork tubes
• Made to fit exactly between the top & bottom of the triple trees with no gap & no rattle
• Sold in Pairs

UPPER FORK COVERS

Suits 18-UP FXBB Models
• Black high-strength aluminum upper fork tube covers to suit 18-UP Street Bob models with 49mm fork tubes
• Made to fit exactly between the top & bottom of the triple trees with no gap & no rattle
• Sold in Pairs

IOMP UPPER FORK COVERS WITH INDICATORS

UPPER FORK COVERS WITH INDICATORS

Suits 13-17 FXSB Models
• Black high-strength aluminum upper fork tube covers with indicators to suit 13-17 Breakout models with 49mm fork tubes
• Made to fit exactly between the top & bottom of the triple trees with no gap & no rattle, cable ducts on the inside, cable exits at the upper fork bridge
• Sold in Pairs

UPPER FORK COVERS WITH INDICATORS

Suits 07-17 Dyna Models
• Black high-strength aluminum upper fork tube covers with indicators to suit 07-17 Dyna models with 49mm fork tubes
• Made to fit exactly between the top & bottom of the triple trees with no gap & no rattle, cable ducts on the inside, cable exits at the upper fork bridge
• Sold in Pairs

UPPER FORK COVERS WITH INDICATORS

Suits 18-UP FXBR Models
• Black high-strength aluminum upper fork tube covers with indicators to suit 18-up Breakout models with 49mm fork tubes
• Made to fit exactly between the top & bottom of the triple trees with no gap & no rattle, cable ducts on the inside, cable exits at the upper fork bridge
• Sold in Pairs

UPPER FORK COVERS WITH INDICATORS

Suits 08-UP FXBB Models
• Black high-strength aluminum upper fork tube covers with indicators to suit 18-up Street Bob models with 49mm fork tubes
• Made to fit exactly between the top & bottom of the triple trees with no gap & no rattle, cable ducts on the inside, cable exits at the upper fork bridge
• Sold in Pairs

CULT WERK FORK COVER KITS

hd-bro028_logo

CW-HD-BRO028

6 Piece Fork Cover Kit With Logo

Suits 18-UP FXBR Models

Complete 6-piece fork cover kit in black with the lower covers made of aluminum or with bellows suitable for Harley-Davidson ® Breakout models from year of construction 2018. With this kit from Cult-Werk you can blend the fork tubes above, between and below the fork bridges. So the fork tubes are covered and the entire fork appears beefier and completely black! This fork cover kit can be used with the original front fender or custom fenders.

The individual covers are fastened with concealed set screws and thus center themselves on the fork tubes. This ensures a secure hold of the cover. To ensure that the gaps between the covers and the fork bridges are exactly parallel, the covers were provided with the same slants as the fork bridges.

Our covers are made of high-quality aluminum and are milled on the latest 5-axis machining centers and then powder-coated in black gloss. This guarantees absolutely the highest quality! The assembly is very simple, the upper and the lower cover are only pushed over the fork tube and screwed tight. On the inside of the lower cover there is a cut-out for freedom of movement on the fender and is therefore hardly visible.

– Kit made of pure aluminum (2x fork caps milled with the CWC logo, 2x upper fork cover & 2x lower fork cover)

cw-hd-bro044

CW-HD-BRO044

6 Piece Fork Cover Kit (Black)

Suits 18-UP FXBR Models

Complete 6-piece fork cover kit in black with the lower covers made of aluminum or with bellows suitable for Harley-Davidson ® Breakout models from year of construction 2018. With this kit from Cult-Werk you can blend the fork tubes above, between and below the fork bridges. So the fork tubes are covered and the entire fork appears beefier and completely black! This fork cover kit can be used with the original front fender or custom fenders.

The individual covers are fastened with concealed set screws and thus center themselves on the fork tubes. This ensures a secure hold of the cover. To ensure that the gaps between the covers and the fork bridges are exactly parallel, the covers were provided with the same slants as the fork bridges.

Our covers are made of high-quality aluminum and are milled on the latest 5-axis machining centers and then powder-coated in black gloss. This guarantees absolutely the highest quality! The assembly is very simple, the upper and the lower cover are only pushed over the fork tube and screwed tight. On the inside of the lower cover there is a cut-out for freedom of movement on the fender and is therefore hardly visible.

– Kit made of pure aluminum (2x fork caps, 2x upper fork cover & 2x lower fork cover)

cw-hd-bro011

CW-HD-BRO011

6 Piece Fork Cover Kit (Black)

Suits 13-17 FXSB Models

Complete 6-piece fork cover kit in black with the lower covers made of aluminum or with bellows suitable for Harley-Davidson ® Breakout models from year of construction 2013 to 2017. With this kit from Cult-Werk you can blend the fork tubes above, between and below the Triple trees. So the fork tubes are covered and the entire fork appears beefier and completely black! This fork cover kit can be used with the original front fender or custom fenders.

The individual covers are fastened with concealed set screws and thus center themselves on the fork tubes. This ensures a secure hold of the cover. To ensure that the gaps between the covers and the fork bridges are exactly parallel, the covers were provided with the same slants as the fork bridges.

Our covers are made of high-quality aluminum and are milled on the latest 5-axis machining centers and then powder-coated in black gloss. This guarantees absolutely the highest quality! The assembly is very simple, the upper and the lower cover are only pushed over the fork tube and screwed tight. On the inside of the lower cover there is a cut-out for freedom of movement on the fender and is therefore hardly visible.

– Kit made of pure aluminum (2x fork caps, 2x upper fork cover & 2x lower fork cover)

hd-dyn018_insitu

CW-HD-DYN018

6 Piece Fork Cover Kit (Black)

Suits 07-17 Dyna Models

Complete 6-piece fork cover kit in black with the lower covers made of aluminum or with bellows suitable for Harley-Davidson ® Dyna models with 49mm fork from year of construction 2007 to current!

With this kit from Cult-Werk you can blend the fork tubes above, between and below the fork bridges. So the fork tubes are covered and the entire fork appears beefier and completely black! This fork cover kit can be used with the original front fender or custom fenders. The individual covers are attached using grub screws and thus center themselves on the fork tubes. This ensures a secure hold!

Our covers are made of high-quality aluminum and are milled on the latest 5-axis machining centers and then powder-coated in black gloss. This guarantees absolutely the highest quality! The assembly is very simple, the upper and the lower cover are only pushed over the fork tube and screwed tight. On the inside of the lower cover there is a cut-out for freedom of movement on the fender and is therefore hardly visible.

– Kit made of pure aluminum (2x fork caps, 2x upper fork cover & 2x lower fork cover)

hd-bro103_insitu

CW-HD-BRO103

6 Piece Fork Cover Kit (Black)

18-UP M8 FXBB Models

Complete 6-piece fork cover kit in black with the fork caps in pure black or with milling suitable for Harley-Davidson ® Street Bob models from year of construction 2018! With this kit from Cult-Werk you can blend the fork tubes above, between and below the fork bridges. So the fork tubes are covered and the entire fork appears beefier and completely black! This fork cover kit can be used with the original front fender or custom fenders. The individual covers are attached using grub screws and thus center themselves on the fork tubes. This ensures a secure hold!

Our covers are made of high-quality aluminum and are milled on the latest 5-axis machining centers and then powder-coated in black gloss. This guarantees absolutely the highest quality! The assembly is very simple, the upper and the lower cover are only pushed over the fork tube and screwed tight. On the inside of the lower cover there is a cut-out for freedom of movement on the fender and is therefore hardly visible.

– without milling (the caps are supplied in pure black)

hd-bro031_insitu

CW-HD-BRO031

2 Piece Lower Fork Cover Kit (Black)

18-UP M8 FXBR Models

Suitable for all Harley-Davidson ® Breakout models from year of construction 2018. With this 2-piece fork cover kit from Cult-Werk you can hide the lower fork tubes below the fork bridge. This way, the chrome-plated fork tubes are covered and the entire fork appears beefier and completely black! The covers are attached using hidden setscrews and thus center themselves on the fork tubes. This ensures a secure hold of the cover. To ensure that the gaps between the covers and the fork bridge are exactly parallel, the covers were provided with the same slants as the fork bridge.

Our covers are made of high-quality aluminum and are milled on the latest 5-axis machining centers and then powder-coated in black gloss. This guarantees absolutely the highest quality! Installation is very simple, the cover is only pushed over the fork tube and screwed tight. This Gable Cover Kit is suitable for the original front fender and for custom fenders.

All parts required for assembly are included!